Universal Antenna Mount

Provides for Easy Installation for

all WiFi Antennas

 

8dBi Outdoor WiFi

Indoor/Outdoor WiFi

Varies on Access Point

 

Part#: GNS-1402

Price: $35.99

 

Click for More Info.

 

 

 

 

5.4-5.8GHz Point to Point Bridge
150Mbps, 802.11N, 2x2 MIMO, Point to Point Wireless Ethernet Bridge, 5GHz 25dBi dual polarity dish antenna, integrated, outdoor bridge AP, WPA/WPA2 Security, POE/PS included.

 

 

Part#: GNS-1153
Price:

$639.99

 

Features:
25dBi External Dish Antenna

AP/CPE Operating Modes

Built In Web Configuration

150Mbps Transfer Rate

802.11n MIMO 2x2

20/40MHz Channel size

 

 

 

 

In StockGNS-1153Contact Us to Buy

 

 

 

Installation:

This complete link ships pre-configured for "out of the box" installation.  No configuration is required.  Web based management allows for adjustment of TX/RX power, Security type, signal strength/signal noise reading, and real time throughput estimates. 

 

Basic Description:

This 802.11N Point to Point Wireless Bridge includes a pair of outdoor access points, that have an integrated 25dBi directional dish antenna built onto the enclosure.  This means that only a single, small enclosure is required at each location.  Once the AP's are installed at each location, the Wireless Bridge operates as a transparent bridge, and will pass all network traffic between your two locations.  The Wireless Bridge operates similar to an invisible Ethernet cable connecting your two locations.  Each antenna has a beam width of about 10, so aligning the antennas is easy.  Furthermore, you will have the ability to view real time signal strength, link quality, and noise level, using the web based configuration.  Each AP has a static IP address, used strictly for web based configuration, and troubleshooting.

 

Connection to Network:

To connect the access point to your network at each location, a single Cat5 Ethernet cable is used.  A 50ft. cable is included for each location.  (If you need more cable, a maximum length of up to 200ft. can be used)  The Cat5 Ethernet cable connects directly from the outdoor access point using a weatherproof grommet,  to an indoor POE (Power-over-Ethernet) injector.  The POE injector plugs into a standard AC outlet for power, and another Cat5 Ethernet cable connects from the POE injector to your network (Router/PC/Switch etc.)

At the MAIN location, you will typically connect to an open LAN port on the back of your existing router, or switch.  At the REMOTE location, you can connect either directly to a PC if you only have a single computer, or you can connect to an indoor wired/wireless router.  This will allow you to run multiple computers over the wireless bridge.  See Diagram below.

 

Maximum Range & Interference:

With clear, un-obstructed line of sight between your two locations, a maximum range of 3 mile can be achieved using this link.  Please note that this Point to Point Wireless Bridge operates between 5.4-5.8GHz.  If you plan on installing more then one link at the same location, you want to avoid interference between each Point to Point link by using separate channels such as CH. 149 (5.7GHz) and CH. 165 (5.8GHz). Mount the outdoor access points as high as possible to further avoid any other 5GHz interference.

 

Each access point has a 23dBm maximum output power.  This works great for long distance Point-to-Point applications, as well as Client applications.  Power can be scaled back for closer installations to avoid noise issues and to meet local regulatory requirements.

 

For applications that require transfer of very large files, video transmission, or large amounts VoIP (Voice over IP) traffic, it is recommended that you choose a FULL DUPLEX, 5GHz Point to Point link, which will not only avoid all 2.4GHz interference, but offer much faster throughput, and lower jitter rates.  A full duplex, Point to Point Wireless Bridge will also offer lower latency, which increases performance.

For distances less then 2 miles, use the following full duplex link: GNS-LIGOPTP-PRO

 

Security Features:

This Wireless Point to Point bridge operates as a transparent bridge.  It is similar to an invisible Ethernet cable connecting your two locations.  It includes multiple security options including WEP/WPA/WPA2.  It also has ability to enable MAC address authentication so that only the two access points are able communicate.  You can hide the network SSID, and because the beam width of the antennas is directional, (about 16) the signal is not being broadcasted in all directions, only in the direction you aim the outdoor antenna.

 

If you have any other questions, please contact our Pre-Sales/Technical Support Dept. at (516) 214-0321.

GNS Wireless has assembled this kit with the components required for a fully configured "out of the box" solution for a wireless point-to-point link.  The IP address for each wireless radio allows you to customize the settings, and view radio configuration tools.

Point to Point Wireless Applications:

  • Cost-effective T-1 or lease line replacement
  • IP-based video surveillance solutions
  • Wireless Point-to-Point between end points
  • WiFi hops between remote end points
  • WiFi links to connect 2 or more devices
  • Remote monitoring
  • Wireless wide area network connectivity
  • Municipal, education, healthcare, security, enterprise and more

 

 


     RELATED PRODUCTS


9dBi Outdoor Omni (360)

Range = 1000ft.  (Pt. to Mp.)

 

Part#: GNS-1401

Price: $89.99

 

 

 

 

....................................

Click for More Info.

....................................

 

 

13dBi Outdoor Directional

Range = 2 miles (Pt. to Pt.)

Point to Point 2.4GHz Wi-Fi

Range Varies on Access Point

 

Part#: GNS-1403

Price: $58.99

 

Click for More Info.

 

 

 

Return Policy | Terms and Conditions | FAQ | About Us | Contact Us



Copyright GNS Wireless LLC., 2014