Universal Antenna Mount

Universal Antenna Mount

Provides for Easy Installation for

all WiFi Antennas



Coax Sealant included.


ACTi ACM1431, ACM-1231

Infrared Network Camera

Easily connects to your existing

PTP Wireless Ethernet Link

Click for more information


 Tech. Support Included


  3 - Year




802.11A, 802.11N

802.11A/N Wireless Ethernet Bridge
802.11N Point to Point Wireless Ethernet Bridge.  Up to 300Mbps Aggregate data rate.  26dBm transmit power with adjustable output for closer installations.  Integrated 17dBi 2x2 MIMO panel antenna, external alignment LED's.  Includes WEP/WPA/WPA2 Security, Power over Ethernet - Complete Link



802.11N Point to Point Wireless Ethernet Bridge.  Up to 300Mbps Aggregate data rate.  26dBm transmit power with adjustable output for closer installations.  Integrated 17dBi 2x2 MIMO panel antenna, external alignment LED's.  Includes WEP/WPA/WPA2 Security, Power over Ethernet - GNS-1120N Complete Link


Part#: GNS-1120N

Call for Pricing


802.11N Point to Point Wireless Ethernet Bridge.  Up to 300Mbps Aggregate data rate.  26dBm transmit power with adjustable output for closer installations.  Integrated 17dBi 2x2 MIMO panel antenna, external alignment LED's.


Whats included in this point to point link:

2x Outdoor Integrated Radio
2x Power over Ethernet Injector (PoE)
2x Power Supply
2x 50ft. Sheilded cat5e Ethernet Cable
2x Pole Mount Hardware for 1-1.5" OD mast

Pre-configured for "out of the box" installation

External signal LEDs to assist with alignment

WEP/WPA/WPA2 (TKIP/AES) Encryption

1 Year Warranty includes Tech Support


The GNS-1120N is a complete link (PAIR)






Not in StockGNS-1120NContact Us to Buy





This complete link ships pre-configured for "out of the box" installation.  No configuration is required.  Web based management allows for adjustment of TX/RX power, Security type, signal strength/signal noise reading, and real time throughput estimates. 


Basic Description:

This Point to Point Wireless Bridge includes a pair of outdoor access points, that have an integrated 17dBi directional patch antenna built into the enclosure.  This means that only a single, small enclosure is required at each location.  Once the AP's are installed at each location, the Wireless Bridge operates as a transparent bridge, and will pass all network traffic between your two locations.  The Wireless Bridge operates similar to an invisible Ethernet cable connecting your two locations.  Each antenna has a beam width of about 10, so aligning the antennas is easy.  Furthermore, you will have the ability to view real time signal strength, link quality, and noise level, using the web based configuration.  Each AP has a static IP address, used strictly for web based configuration, and troubleshooting.



Connection to Network:

To connect the access point to your network at each location, a single Cat5 Ethernet cable is used.  A 50ft. cable is included for each location.  (If you need more cable, a maximum length of up to 200ft. can be used)  The Cat5 Ethernet cable connects directly from the outdoor access point using a weatherproof grommet,  to an indoor POE (Power-over-Ethernet) injector.  The POE injector plugs into a standard AC outlet for power, and another Cat5 Ethernet cable connects from the POE injector to your network (Router/PC/Switch etc.)

At the MAIN location, you will typically connect to an open LAN port on the back of your existing router, or switch.  At the REMOTE location, you can connect either directly to a PC if you only have a single computer, or you can connect to an indoor wired/wireless router.  This will allow you to run multiple computers over the wireless bridge.  See Diagram below.


Maximum Range & Interference:

With clear, un-obstructed line of sight between your two locations, a maximum range of 3/4 mile can be achieved using this link.  Please note that this Point to Point Wireless Bridge operates between 5.3-5.8GHz.  If you plan on installing more then one link at the same location, you want to avoid interference between each Point to Point link by using separate channels such as CH. 60 (5.3GHz) and CH. 149 (5.7GHz). Mount the outdoor access points as high as possible to further avoid any other 5GHz interference.


Each access point has a 26dBm maximum output power.  This works great for long distance Point-to-Point applications, as well as Client applications.  Power can be scaled back for closer installations to avoid noise issues and to meet local regulatory requirements.


For applications that require transfer of large files, video transmission, or VoIP (Voice over IP), it is recommended that you choose a 5GHz Point to Point link, which will avoid all 2.4GHz interference.  This will not only increased distance, and more reliability, but also faster speed, and higher throughput.  A 5GHz Point to Point Wireless Bridge will also offer lower latency, which increases performance.

Click here for a short range, 5GHz Point to Point Wireless Bridge, GNS-1120A.


Security Features:

This Wireless Point to Point bridge operates as a transparent bridge.  It is similar to an invisible Ethernet cable connecting your two locations.  It includes multiple security options including WEP/WPA/WPA2.  It also has ability to enable MAC address authentication so that only the two access points are able communicate.  You can hide the network SSID, and because the beam width of the antennas is directional, (about 10) the signal is not being broadcasted in all directions, only in the direction you aim the outdoor antenna.


If you have any other questions, please contact our Pre-Sales/Technical Support Dept. at (516) 214-0321.


Ask us about pre-configuration of these Access Points, so they work "out of the box" and ready to install on your local area network.



For additional protection from surges, or other surge induced electricity that

may travel through the Ethernet cable, please use the inline surge protector.

This would be placed inline between the outdoor access point, and the indoor

POE injector.  It can be placed either outdoors, or indoors.


Indoor/Outdoor Canopy Surge Protector


Part#: 300SSB

Price: $32.99



  • More Robost Routing Features:  Includes Tunneling Protocol Support, which will allow you to pass through VPN clients, as well as use tunneling protocols such as VPN, PPTP, RSA and others.

  • All New Access Point Features:  WDS will allow this Outdoor Access Point to be wirelessly connected to other Access Points, while still servicing clients.  (Wireless Distribution System)

  • Wi-Fi Protected Access (WPA):  Wireless Protected Access improves on the security features of WEP.  It includes improved data encryption and user authentication, and AES Encryption.

  • All New Client Adapter Features:  With this Outdoor Access Point, you will be able to align your client and point-to-point installations without having to log into the radio.  You will get visual signal strength at a glance by using this great new feature, using the alignment LED's located on the back of the Access Point.

  • Controllable High Gain Output:  Both radios have 26dBm maximum output.  This works great for long distance Point-to-Point applications, as well as Client applications.  Power can be scaled back for closer installations to avoid noise issues and to meet local regulatory requirements.

  • Wireless Security:  WEP, WPA wireless security is included in this wireless backhaul.  This will encrypt the data being sent between the connection.  Also included in this wireless backhaul is AES encryption, which is a higher level security feature then standard WEP/WPA.  The two radios can also be configured in PXP mode, which enables only the two outdoor access points to communicate with each other, avoiding any other access to the network.  The wireless bridge operates seamlessly as a Wireless Bridge between your two locations.

  • Wireless Interference:  This wireless Ethernet Bridge is operating at 5GHz.  At most locations, this frequency is used less frequently then the standard 802.11b/g, so interference is usually minimized.  If you experience interference at this frequency, check that your antennas are not mounted directly on a metal surface, have line of sight between each other, and try changing the channel to one that is available .  You may also want to move to a 802.11b/g, 2.4GHz wireless bridge. Click here for an 802.11b/g wireless bridge.



Antenna Specifications
Frequency Range: 5300 - 5800 MHz
Gain: 17 dBi MIMO
Polarization: Dual Polarized
AZ/EL Beamwidth: 30/17
Front to Back Ratio: 26 dB
VSWR 50 Ohm: < 1.5
Wind Load: 125 mph (200 km/h)
Size: 10" x 8" x 3.5"
Combined Weight: 2 lbs with radio
Connector: Outdoor RJ-45 All Weather
Mounting Kit/Style: Included: Pole Mount (1" - 1.5" Diameter)
Operating Temperature: -40C to 70C
Material: ABS
Additional Features: UV Stabilized
Radio Specifications
Standard Compliance: IEEE 802.11a/n (300 Mbps)
Modulation: OFDM52: 64QAM , 64QAM , 64QAM , 16QAM , 16QAM , QPSK , QPSK , BPSK
Channel Bandwidths: 5MHz, 10MHz, 20MHz, 20/40MHz Selectable
Frequency Band: 5100 - 5900 MHz
Data Rate: up to 300Mbps
Output Power: (500mW) up to 26 dBm - Adjustable
Receive Sensitivity:

802.11a: -97 +/- 2dBm @ 6 Mbps, -80 +/- 2dBm @ 54 Mbps

Data Security: WPA, WPA2 & 64/128 bit WEP Data Security, MAC Filtering
DC Power Input: 18 VDC Adapter, PoE injector
Warranty 3-Year

Specifications are subject to change without notice.

Subject to local regulations.


When connecting the Outdoor Cat5 Ethernet cable to the access point, the below image will illustrate how to feed the cat5 cable through the weatherproof adapter, and into the Ethernet port on the access point.  Once tightened, this will provide a weatherproof seal for the RJ45 connector.  Please contact us with any questions.



In StockGNS-1120NContact Us to Buy






Real Time Signal Strength Meter:

Once the Wireless Link is established between your two locations, you will be able to log into the web interface of the AP and view real time noise and signal strength levels.  This will allow you to adjust the antennas accordingly and make any necessary changes required in order for your wireless link to operate at its fullest potential.

The image to the right is an example of the Noise and Signal levels that will allow you to monitor the Wireless Bridge.

SNR = Noise (dBm) - Signal (dBm)

Signal to Noise ratio, Wireless signal strength, gnswireless.com


 View Point to Point Wireless Installation Diagram Below:

NOTE: Linksys routers and universal antenna mounts are for illustration purposes only and are not included in the bridge package.


Please Note: The wireless bridge kits listed on this page may also be referred to as 802.11 bridge  802.11 Ethernet bridge, 802.11g wireless bridge, belkin wireless bridge, d link wireless bridge , dlink wifi repeater, dlink wireless bridge, Ethernet bridge router, how to wireless bridge, internet wireless bridge, Linksys point to point wireless , Linksys wifi bridge, Linksys wifi repeater, long range wifi bridge, long range wireless Ethernet bridge, netgear network bridge, netgear wireless bridge, netgear wireless network bridge, outdoor access point bridge, outdoor Ethernet bridge, outdoor wifi bridge, outdoor wireless access point, outdoor wireless bridges, outdoor wireless Ethernet bridge, outdoor wireless point to point, point to multipoint bridge, point to point Ethernet bridge, point to point network connection, point to point router, point to point wifi bridge, point to point wireless bridging, point to point wireless connection, point to point wireless Ethernet, point to point wireless internet, point to point wireless networks, secure wireless bridge, set up wireless bridge, setting up wireless bridge, wifi bridge router, wifi client bridge, wireless access point bridge, wireless bridge access point, wireless bridge antenna, wireless bridge connection, wireless bridge kits, wireless bridge point to multipoint, wireless bridge router, wireless bridge setup, wireless bridge wds, wireless lan bridge, wireless network bridge Ethernet, wireless network bridge, wireless networking bridge, wireless repeater bridge, wireless to wireless bridge, 5GHz point to point wireless backhaul, T1 replacement wireless bridge, T1 point to point, Fiber wireless backhaul.


Universal Antenna Mount

Easy Installation for all Antennas


Part#: GNS-1433

Price: $27.99





Click for More Info.



antenna tripod

3 foot Antenna Tripod

Requires min. 5ft. Mast


Part#: GNS-1631

Price: $44.99




Click for More Info.


wall mount bracket

12" Wall Mount Bracket

Great for when eve of build-

ing is in the way of antenna.


Part#: GNS-1633

Price: $22.99



Click for More Info.




Ask us about pre-configuration of these Access Points, so they work "out of the box" and ready to install at your two locations.  




Return Policy | Terms and Conditions | FAQ | About Us | Contact Us

Copyright GNS Wireless LLC., 2014

All Major Cards Accepted