Universal Antenna Mount

Provides for Easy Installation for

all Wi Fi Antennas

 

 

Coax Sealant included.

 

 

900Mhz Wireless Ethernet Bridge
900Mhz Point to Point Wireless Ethernet Bridge.  Up to 11Mbps Aggregate data rate.  23dBm transmit power with adjustable output for closer installations.  Integrated 12dBi panel antenna.  Includes WEP/WPA/WPA2 Security, Power over Ethernet - Complete Link - 1/4 Mile NLOS

 

 

900Mhz Point to Point Wireless Ethernet Bridge.  Up to 11Mbps Aggregate data rate.  23dBm transmit power with adjustable output for closer installations.  Integrated 12dBi panel antenna.  Includes WEP/WPA/WPA2 Security, Power over Ethernet - Complete Link - 1/4 Mile NLOS

 

Part#: GNS-1138
Price:

$989.95

 

Features:
Integrated 12dBi Patch Antennas

Weather Proof Enclosures

Carrier Class QOS with Low Latency

11Mbps Aggregate Data Rate

Integrated PoE/PS Injectors included

U-Bolts for mounting to a pole

Pair of 50ft. cat5 network cable included

External Alignment/Signal LED's

VLAN Transparent Support

Adjustable Transmit TX power

Web & SNMP based Management

 

 

 

 

 

In StockGNS-1138Contact Us to Buy

 

 

ZERO CONFIGURATION needed as this

wireless bridge comes ready to install "out of the box"

 

Basic Description:

This 900MHz Point to Point Wireless Bridge includes a pair of outdoor access points, that have an integrated 12dBi directional patch antenna built into the enclosure.  This means that only a single, small enclosure is required at each location.  Once the AP's are installed at each location, the Wireless Bridge operates as a transparent bridge, and will pass all network traffic between your two locations.  The Wireless Bridge operates similar to an invisible Ethernet cable connecting your two locations.  Each antenna has a beam width of about 40, so aligning the antennas is easy.  Furthermore, you will have the ability to view real time signal strength, link quality, and noise level, using the web based configuration.  Each AP has a static IP address, used strictly for web based configuration, and troubleshooting.

 

Connection to Network:

To connect the access point to your network at each location, a single Cat5 Ethernet cable is used.  A 50ft. cable is included for each location.  (If you need more cable, a maximum length of up to 200ft. can be used)  The Cat5 Ethernet cable connects directly from the outdoor access point using a weatherproof grommet,  to an indoor POE (Power-over-Ethernet) injector.  The POE injector plugs into a standard AC outlet for power, and another Cat5 Ethernet cable connects from the POE injector to your network (Router/PC/Switch etc.)

At the MAIN location, you will typically connect to an open LAN port on the back of your existing router, or switch.  At the REMOTE location, you can connect either directly to a PC if you only have a single computer, or you can connect to an indoor wired/wireless router.  This will allow you to run multiple computers over the wireless bridge.  See Diagram below.

 

Maximum Range & Interference:

With clear, un-obstructed line of sight between your two locations, a maximum range of 1 mile can be achieved using this link.  When trees are present between your two locations, maximum distance is estimated at 1/4 mile.  (Please note that exact distance with obstruction may depend on external interference) Please note that because this Point to Point Wireless Bridge operates at 900MHz, external interference from other cellular networks may slow down the transmission speed of the link, and even cause dropouts.  To avoid interference between the Point to Point Wireless Bridge, and indoor wireless routers, or access points that may be present at each of your locations, you want to install the antennas as high as possible, and avoid as much obstruction as possible.

 

Each access point has a 23dBm maximum output power.  This works great for long distance Point-to-Point applications, as well as Client applications.  Power can be scaled back for closer installations to avoid noise issues and to meet local regulatory requirements.

 

Security Features:

This Wireless Point to Point bridge operates as a transparent bridge.  It is similar to an invisible Ethernet cable connecting your two locations.  It includes multiple security options including WEP/WPA/WPA2.  It also has ability to enable MAC address authentication so that only the two access points are able communicate.  You can hide the network SSID, and because the beam width of the antennas is directional, (about 40) the signal is not being broadcasted in all directions, only in the direction you aim the outdoor antenna.

 

If you have any other questions, please contact our Pre-Sales/Technical Support Dept. at (516) 214-0321.

 

Ask us about pre-configuration of these Access Points, so they work "out of the box" and ready to install on your local area network.

 

Features at a glance:

  • Wi-Fi Protected Access (WPA):  Wireless Protected Access improves on the security features of WEP.  It includes improved data encryption and user authentication.

  • Controllable High Gain Output:  Both radios have 24dBm maximum output.  This works great for long distance Point-to-Point applications, as well as Client applications.  Power can be scaled back for closer installations to avoid noise issues and to meet local regulatory requirements.

  • 5 Ultra Bright LED's:  External LED's assist in antenna alignment, and ease of installation

  • Adjustable Transmit Power:  This wireless bridge can be used for short distance connections, or medium range point to point connections of up to 1 mile, by adjusting the output power of the radios.  Maximum power output is 200mW.

For additional protection from surges, or other surge induced electricity that

may travel through the Ethernet cable, please use the 300SS surge protector.

 

Indoor/Outdoor Canopy Surge Protector

 

Part#: 300SSB

Price: $32.99


 

Antenna Specifications
Frequency Range: 902-928 MHz
Gain: 12.5 dBi
Maximum Input Power: 30Watts
Polarization: Vertical or Horizontal
AZ/EL Beamwidth: 42
Front to Back Ratio: > 25dB
VSWR 50 Ohm: ≥ 1.7:1
Wind Load: 125 mph
Size: 15.4" x 15.4" x 1.7"
Combined Weight: 2.2 lbs
Connector: Integral Type N-Jack
Mounting Kit/Style: Included: Pole Mount
Operating Temperature: -45C to + 65C
Material: ABS
Radio Specifications
Standard Compliance: IEEE 802.11b/g
Modulation: OFDM w/BPSK, QPSK, 16 QAM, 64 QAM
Frequency Band: 900 - 928 MHz
Data Rate: 54, 48, 36, 23, 18, 12, 11, 9, 6, 5.5 and 1
Output Power: (200mW) 23dBm (+/- 1.5dB) @ 1-24 Mbps
Receive Sensitivity: -92dBm @ 6Mbps
RF Channels: 2 Channels; 913, 918 MHz
Data Security: WPA/WPA2, 64/128 bit WEP MAC Address Filter
DC Power Input: 48 VDC Adapter, PoE with Surge Protection,
IEEE 802.3af compliant
Operating Temperature: -40 C to + 70 C
Ethernet Connection: 10/100 BaseT Auto MDI/MDX

 

 

 

 

 

 

 

 
 

 

 View Point to Point Wireless Installation Diagram Below:

NOTE: Linksys routers and universal antenna mounts are for illustration purposes only and are not included in the bridge package.

 

Please Note: The wireless bridge kits listed on this page may also be referred to as 802.11 bridge  802.11 Ethernet bridge, 802.11g wireless bridge, belkin wireless bridge, d link wireless bridge , dlink wifi repeater, dlink wireless bridge, Ethernet bridge router, how to wireless bridge, internet wireless bridge, Linksys point to point wireless , Linksys wifi bridge, Linksys wifi repeater, long range wifi bridge, long range wireless Ethernet bridge, netgear network bridge, netgear wireless bridge, netgear wireless network bridge, outdoor access point bridge, outdoor Ethernet bridge, outdoor wifi bridge, outdoor wireless access point, outdoor wireless bridges, outdoor wireless Ethernet bridge, outdoor wireless point to point, point to multipoint bridge, point to point Ethernet bridge, point to point network connection, point to point router, point to point wifi bridge, point to point wireless bridging, point to point wireless connection, point to point wireless Ethernet, point to point wireless internet, point to point wireless networks, secure wireless bridge, set up wireless bridge, setting up wireless bridge, wifi bridge router, wifi client bridge, wireless access point bridge, wireless bridge access point, wireless bridge antenna, wireless bridge connection, wireless bridge kits, wireless bridge point to multipoint, wireless bridge router, wireless bridge setup, wireless bridge wds, wireless lan bridge, wireless network bridge Ethernet, wireless network bridge, wireless networking bridge, wireless repeater bridge, wireless to wireless bridge, 5GHz point to point wireless backhaul, T1 replacement wireless bridge, T1 point to point, Fiber wireless backhaul.
 
 RELATED MOUNTING HARDWARE:

*RECOMMENDED

Universal Antenna Mount

Easy Installation for all Antennas

 

Part#: GNS-1433

Price: $27.99

 

 

....................................

 

Click for More Info.

 

....................................

3 foot Antenna Tripod

Requires min. 5ft. Mast

 

Part#: GNS-1631

Price: $44.99

 

 

....................................

Click for More Info.

....................................

12" Wall Mount Bracket

Great for when eve of build-

ing is in the way of antenna.

 

Part#: GNS-1633

Price: $22.99

....................................

 

Click for More Info.

 

....................................

 

Ask us about pre-configuration of these Access Points, so they work "out of the box" and ready to install at your two locations.  

 

 

 
 
   

Return Policy | Terms and Conditions | FAQ | About Us | Contact Us



Copyright GNS Wireless LLC., 2014

All Major Cards Accepted