Universal Antenna Mount

Universal Antenna Mount

Provides for Easy Installation for

all WiFi Antennas



Coax Sealant included.


ACTi ACM1431, ACM-1231

Infrared Network Camera

Easily connects to your existing

PTP Wireless Ethernet Link

Click for more information




 54Mbps Outdoor Point-to-Point Backhaul (1/2 Mile LOS)

 802.11b/g 2.4GHz Wireless Ethernet Bridge - COMPLETE LINK



54Mbps Point to Point Wireless.

All inclusive Outdoor Antennas

Point to Point wireless bridge, outdoor wireless network, long range wireless network, PTP Backhaul, GNS-1140


Part#: GNS-1140



Integrated 15dBi Patch Antennas

Weather Proof Enclosures

Carrier Class QOS with Low Latency

802.11g 54Mbps Transfer Rate

Integrated PoE Injectors included

U-Bolts for mounting to a pole

Pair of 25ft. cat5 network cable included

Great for Sharing Internet/Files



If you have an abundant amount of 2.4GHz wireless networks in the area, use the GNS-1120A for a more stable point to point connection.





Call for availabilityGNS-1140Contact Us to Buy



Outdoor Access Points = Ease of Installation


wireless bridge comes ready to install "out of the box".

Point.  Shoot.  Connected...


Basic Description:

This Point to Point Wireless Bridge includes a pair of outdoor access points, that have an integrated 15dBi directional patch antenna built into the enclosure.  This means that only a single, small enclosure is required at each location.  Once the AP's are installed at each location, the Wireless Bridge operates as a transparent bridge, and will pass all network traffic between your two locations.  The Wireless Bridge operates similar to an invisible Ethernet cable connecting your two locations.  Each antenna has a beam width of about 26, so aligning the antennas is easy.  Furthermore, you will have the ability to view real time signal strength, link quality, and noise level, using the web based configuration.  Each AP has a static IP address, used strictly for web based configuration, and troubleshooting.


Connection to Network:

To connect the access point to your network at each location, a single Cat5 Ethernet cable is used.  A 25ft. cable is included for each location.  (If you need more cable, a maximum length of up to 200ft. can be used)  The Cat5 Ethernet cable connects directly from the outdoor access point using a weatherproof grommet,  to an indoor POE (Power-over-Ethernet) injector.  The POE injector plugs into a standard AC outlet for power, and another Cat5 Ethernet cable connects from the POE injector to your network (Router/PC/Switch etc.)

At the MAIN location, you will typically connect to an open LAN port on the back of your existing router, or switch.  At the REMOTE location, you can connect either directly to a PC if you only have a single computer, or you can connect to an indoor wired/wireless router.  This will allow you to run multiple computers over the wireless bridge.  See Diagram below.


Maximum Range & Interference:

With clear, un-obstructed line of sight between your two locations, a maximum range of 1/2 mile can be achieved using this link.  Please note that because this Point to Point Wireless Bridge operates at 2.4GHz, external interference from other 2.4GHz wireless networks may slow down the transmission speed of the link, and even cause dropouts.  To avoid interference between the Point to Point Wireless Bridge, and indoor wireless routers, or access points that may be present at each of your locations, you will have the ability to change the transmission channel that the outdoor wireless bridge is operating on.  Channels 1, 6 and 11 are the most popular, as they are non-overlapping channels and will not interfere with each other.  You also want to mount the outdoor access points as high as possible to further avoid any local 2.4GHz interference.


Each access point has a 27dBm maximum output power.  This works great for long distance Point-to-Point applications, as well as Client applications.  Power can be scaled back for closer installations to avoid noise issues and to meet local regulatory requirements.


For applications that require transfer of large files, video transmission, or VoIP (Voice over IP), it is recommended that you choose a 5GHz Point to Point link, which will avoid all 2.4GHz interference.  This will not only increased distance, and more reliability, but also faster speed, and higher throughput.  A 5GHz Point to Point Wireless Bridge will also offer lower latency, which increases performance over the point to point link.

Click here for a short range, 5GHz Point to Point Wireless Bridge, GNS-1120A.


Security Features:

This Wireless Point to Point bridge operates as a transparent bridge.  It is similar to an invisible Ethernet cable connecting your two locations.  It includes multiple security options including WEP/WPA/WPA2.  It also has ability to enable MAC address authentication so that only the two access points are able communicate.  You can hide the network SSID, and because the beam width of the antennas is directional, (about 26) the signal is not being broadcasted in all directions, only in the direction you aim the outdoor antenna.


If you have any other questions, please contact our Pre-Sales/Technical Support Dept. at (516) 214-0321.


Ask us about pre-configuration of these Access Points, so they work "out of the box" and ready to install on your local area network.



For additional protection from surges, or other surge induced electricity that

may travel through the Ethernet cable, please use the inline surge protector.

This would be placed inline between the outdoor access point, and the indoor

POE injector.  It can be placed either outdoors, or indoors.


Indoor/Outdoor Canopy Surge Protector


Part#: 300SSB

Price: $32.99



Antenna Specifications
Frequency Range: 2300 - 2500 MHz
Gain: 15 dBi
Maximum Input Power: 50 W
Polarization: Vertical or Horizontal
AZ/EL Beamwidth: 27/26
Front to Back Ratio: 26 dB
VSWR 50 Ohm: < 1.5
Wind Load: 125 mph (200 km/h)
Size: 8" x 8" x 3.5"
Combined Weight: 4 lbs with radio
Connector: Outdoor RJ-45 All Weather
Mounting Kit/Style: Included: Pole Mount (1" - 1.5" Diameter)
Operating Temperature: -25C to 65C
Material: ABS
Additional Features: UV Stabilized
Radio Specifications
Standard Compliance: IEEE 802.11b/g (54 Mbps)
Modulation: OFDM w/BPSK, QPSK, 16 QAM, 64 QAM
Frequency Band: 2412 - 2462 MHz
Data Rate: 54, 48, 36, 23, 18, 12, 11, 9, 6, 5.5 and 1
Output Power: (500mW) up to 27 dBm - Adjustable
Receive Sensitivity:

802.11g: -93 +/- 2dBm @ 6 Mbps, -75 +/- 2dBm @ 54 Mbps

802.11b: -96 +/- 2dBm @ 1 Mbps, -90 +/- 2dBm @ 11 Mbps

RF Channels: Total of 3 Non-overlapping channels
Data Security: WPA, WPA2 & 64/128 bit WEP Data Security, MAC Filtering
DC Power Input: 18 VDC Adapter, PoE injector
Operating Temperature: -25C to 65C
Warranty 1-Year

Specifications are subject to change without notice.

Subject to local regulations.


When connecting the Outdoor Cat5 Ethernet cable to the access point, the below image will illustrate how to feed the cat5 cable through the weatherproof adapter, and into the Ethernet port on the access point.  Once tightened, this will provide a weatherproof seal for the RJ45 connector.  Please contact us with any questions.

Outdoor Ethernet Cat5 cable, Weatherproof RJ45


Call for availabilityGNS-1140Contact Us to Buy






 View Point to Point Wireless Installation Diagram Below:

Point to Point Wireless Bridge Diagram, Diagram of Outdoor Wireless Network

NOTE: Linksys routers and universal antenna mounts are for illustration purposes only and are not included in the bridge package.


Please Note: The wireless bridge kits listed on this page may also be referred to as 802.11 bridge  802.11 Ethernet bridge, 802.11g wireless bridge, belkin wireless bridge, d link wireless bridge , dlink wifi repeater, dlink wireless bridge, Ethernet bridge router, how to wireless bridge, internet wireless bridge, Linksys point to point wireless , Linksys wifi bridge, Linksys wifi repeater, long range wifi bridge, long range wireless Ethernet bridge, netgear network bridge, netgear wireless bridge, netgear wireless network bridge, outdoor access point bridge, outdoor Ethernet bridge, outdoor wifi bridge, outdoor wireless access point, outdoor wireless bridges, outdoor wireless Ethernet bridge, outdoor wireless point to point, point to multipoint bridge, point to point Ethernet bridge, point to point network connection, point to point router, point to point wifi bridge, point to point wireless bridging, point to point wireless connection, point to point wireless Ethernet, point to point wireless internet, point to point wireless networks, secure wireless bridge, set up wireless bridge, setting up wireless bridge, wifi bridge router, wifi client bridge, wireless access point bridge, wireless bridge access point, wireless bridge antenna, wireless bridge connection, wireless bridge kits, wireless bridge point to multipoint, wireless bridge router, wireless bridge setup, wireless bridge wds, wireless lan bridge, wireless network bridge Ethernet, wireless network bridge, wireless networking bridge, wireless repeater bridge, wireless to wireless bridge, 5GHz point to point wireless backhaul, T1 replacement wireless bridge, T1 point to point, Fiber wireless backhaul.


Universal Antenna Mount

Easy Installation for all Antennas


Part#: GNS-1433

Price: $27.99





Click for More Info.



antenna tripod

3 foot Antenna Tripod

Requires min. 5ft. Mast


Part#: GNS-1631

Price: $44.99




Click for More Info.


wall mount bracket

12" Wall Mount Bracket

Great for when eve of build-

ing is in the way of antenna.


Part#: GNS-1633

Price: $22.99



Click for More Info.




Ask us about pre-configuration of these Access Points, so they work "out of the box" and ready to install at your two locations.  




Return Policy | Terms and Conditions | FAQ | About Us | Contact Us

Copyright GNS Wireless LLC., 2014

All Major Cards Accepted